Now you can keep your keg fresher longer with these awesome Co2 Keg Tapping Systems from Beverage Factory! If you get to our shop before we have it available please excuse us as we have 100's of products to get loaded. The is, by far, the most popular beer coupler used in bars, taverns, and pubs worldwide. This sankey coupler kit helps you make sure that you get the right hook-up from your keg and the correct pour from your picnic-cooler setup, jockey box, or coil cooler. Remove the cover from the beer-line intake valve located on top of the keg. If that is all you are planning on drinking out of your kegerator, then this would be the coupler you should choose.
We have multiple options to help you convert a single-tap tower to a dual-tap or triple-tap. Here at Rapids Wholesale, you can choose from a wide selection of beer keg couplers depending on what you need for your bar, tavern, and pub's beer-dispensing system. Am I doomed to now buy pony kegs, or sixth kegs and figure out how the heck to clean and fill these puppys? Did you know that Sankey isn't an official name for a coupler? It fits all domestic brand kegs, as well as 95% of American beers. Make sure that the cylinder is filled and the valve is closed. Make sure the faucet is vertical with the black handle facing the ceiling, and the faucet should be screwed on tightly. For about the 3rd time I cleaned the lines and parts with the cleaning kit I got from your site. Slide the keg in slowly, ensuring that it is properly located, and all hoses are clear of obstructions.
I tried many plugs that work for other items. If you have questions or need something right away just drop us a line. I had to read the post again to make sure I'm actually the getting what GeeL is asking and not what's being implied by the advice given. When done, carefully set the unit upright. Pull on the pressure relief valve to allow gas to vent and give you an accurate reading on the pressure gauge, then calibrate the regulator to the recommended serving pressure for your beer.
Then, carefully tilt the beer keg 17 and rest the edge on the keg floor support on the bottom of the interior cabinet. Pros: This kit was very easy to install and works great. The will tap most American or Canadian domestic kegs including Yuengling, Miller, Budweiser and almost all beers brewed in North America. Close door and enjoy some refreshing draft beer! About Author Plagued by a chronic case of curiosity, Jeff Flowers is just a dude that annoys everyone around him with his loquacious goofiness. It takes minutes to change over.
This is an easy-to-use Taprite low profile keg coupler ideal for tight-clearance installations with a nickel-plated brass body and probe. We do not sell the cheaper wing version usually provided by department and hardware stores catering to the homeowner and not the commercial industry where quality counts. Insert the neoprene washer 14 into the beer line hex nut the beer line is the line coming from the tower and faucet. Check out this from Taprite, also available here at Rapids. Line the notches of the key coupler at the end of the beer line with the slits in the beer-line intake valve on top of the keg. Types of Keg Tap Couplers Below are the different types of beer couplers that are commonly used by bar owners worldwide: 1.
So what more do you need for your bar's beer-dispensing system? Now I swear one night years ago after several Belgian Strong Ales I saw somewhere, internet perchance , a convertor that did exactly this. We also have a single-valve Draught Tech keg coupler with available. Depending on what you have in your kegerator, you may need a different type of coupler in order to serve it correctly. These amazing D System Couplers are designed to be used with American Kegs, also known as Sankey Kegs. A: With the shut-off valve on the regulator 6 closed, open the valve on the gas cylinder 8 completely. With this system D Jockey Box Beer Cooler tap setup, you can conveniently hook up your beer keg to any picnic-cooler setup or jockey box available here at Rapids Wholesale.
The mostly fits New Castle, Heineken, Murphy's Stout, Amstel Light, and lots more brands. This is an Rapids beer coupler ideal for tapping domestic brands of kegged beer, which include most North American beers like Budweiser, Coors, Miller, Anheuser-Busch, and more. Other Taprite-brand keg couplers available here at Rapids include , , and. I would be hesitant to go this route, however, as it may be more expensive to buy the parts individually, and you may miss one or two which will create headaches for you. The type of coupler you need will depend on where that specific beer was kegged.
Just got a kegerator for Christmas. Thanks MyloFiore for the kind reply. If you want to dispense frothy pints of Guinness you will need the , which will also work for Harp Lager and Kilkenny. Always in stock but plan ahead around St. I have no idea whats causing it.